Yamaha WR250X Page 96 Owner'S Manual Download

Page: 96 / 112

SPECIFICATIONS

9-2

Transmission type:

Constant mesh 6-speed

Operation:

Left foot operation

Gear ratio:

1st:

37/14 (2.642)

2nd:

29/16 (1.813)

3rd:

29/22 (1.318)

4th:

26/25 (1.040)

5th:

24/27 (0.888)

6th:

22/28 (0.786)

Chassis:

Frame type:

Semi double cradle

Caster angle:

25.33 °

Trail:

76.0 mm (2.99 in)

Front tire:

Type:

With tube

Size:

110/70R17M/C 54H

Manufacturer/model:

BRIDGESTONE/BT090F RADIAL G

Rear tire:

Type:

With tube

Size:

140/70R17M/C 66H

Manufacturer/model:

BRIDGESTONE/BT090R RADIAL G

Loading:

Maximum load:

WR25XZ 185 kg (408 lb)
WR25XZC 184 kg (406 lb)
(Total weight of rider, passenger, cargo and
accessories)

Tire air pressure (measured on cold
tires):

Loading condition:

0–90 kg (0–198 lb)
Front:

200 kPa (2.00 kgf/cm², 29 psi)

Rear:

200 kPa (2.00 kgf/cm², 29 psi)

Loading condition:

WR25XZ 90–185 kg (198–408 lb)
WR25XZC 90–184 kg (198–406 lb)
Front:

200 kPa (2.00 kgf/cm², 29 psi)

Rear:

225 kPa (2.25 kgf/cm², 33 psi)

Front wheel:

Wheel type:

Spoke wheel

Rim size:

17M/C x MT3.00

Rear wheel:

Wheel type:

Spoke wheel

Rim size:

17M/C x MT4.00

Front brake:

Type:

Single disc brake

Operation:

Right hand operation

Recommended fluid:

DOT 4

Rear brake:

Type:

Single disc brake

Operation:

Right foot operation

Recommended fluid:

DOT 4

Front suspension:

Type:

Telescopic fork

Spring/shock absorber type:

Coil spring/oil damper

Wheel travel:

270.0 mm (10.63 in)

Rear suspension:

Type:

Swingarm (link suspension)

Spring/shock absorber type:

Coil spring/gas-oil damper

Wheel travel:

265.0 mm (10.43 in)

Electrical system:

Ignition system:

TCI (digital)

U32C15E0.book Page 2 Tuesday, July 14, 2009 11:43 AM

Summary of Contents for WR250X

















































































































Search results

Summary of Contents for WR250X

Reviews:

Related manuals for WR250X

Brands by name

Popular brands

Yamaha WR250X, Owner'S Manual

Search results

Summary of Contents for WR250X

Reviews:

Related manuals for WR250X

Brands by name

Popular brands