Yamaha WR250X Page 64 Owner'S Manual Download

Page: 64 / 112

PERIODIC MAINTENANCE AND ADJUSTMENT

7-19

5. Apply oil of the recommended type

to the entire surface of the sponge
material, and then squeeze the ex-
cess oil out.

TIP

The sponge material should be wet but
not dripping.

6. Pull the sponge material over the

air filter element frame.

7. Insert the air filter element into the

air filter case.

NOTICE:

Make sure

that the air filter element is prop-
erly seated in the air filter case.
The engine should never be op-
erated without the air filter ele-
ment installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.

[ECA10481]

8. Place the holding clip in the origi-

nal position.

9. Close the air filter case cover, and

then install the screw.

10. Install the panel.

To clean the air filter check hose

1. Check the hose at the bottom of

the air filter case for accumulated
dirt or water.

2. If dirt or water is visible, remove

the hose, clean it, and then install
it.

1. Sponge material
2. Air filter element frame

Recommended oil:

Yamaha foam air filter oil or other
quality foam air filter oil

1. Air filter check hose

U32C15E0.book Page 19 Tuesday, July 14, 2009 11:43 AM

Summary of Contents for WR250X

















































































































Search results

Summary of Contents for WR250X

Reviews:

Related manuals for WR250X

Brands by name

Popular brands

Yamaha WR250X, Owner'S Manual

Search results

Summary of Contents for WR250X

Reviews:

Related manuals for WR250X

Brands by name

Popular brands