manualshive.com logo in svg

Yamaha WR250F 2022, Owner'S Service Manual


Share
Download
background image

REAR BRAKE

4-33

4. Check:

•

Brake fluid level
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-23.

5. Check:

•

Brake pedal operation
A softy or spongy feeling 

 Bleed the brake

system.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” on page 3-25.

EAM30042

REMOVING THE REAR BRAKE CALIPER

TIP

Before disassembling the brake caliper, drain
the brake fluid from the entire brake system.

1. Remove:

•

Union bolt

•

Copper washer

•

Brake hose

TIP

Put the end of the brake hose into a container
and pump out the brake fluid.

EAM30043

DISASSEMBLING THE REAR BRAKE 

CALIPER

1. Remove:

•

Brake caliper piston “1”

•

Brake caliper piston seal kit “2”

a. Blow compressed air into the brake hose

joint opening to force out the piston from
the brake caliper.

WARNING

EWA13550

• Cover the brake caliper piston with a rag.

Be careful not to get injured when the pis-

ton is expelled from the brake caliper.

• Never try to pry out the brake caliper pis-

ton.

b. Remove the brake caliper piston dust seal

and the brake caliper piston seal.

EAM30044

CHECKING THE REAR BRAKE CALIPER

1. Check:

•

Brake caliper piston “1”
Rust/scratches/wear 

 Replace the brake

caliper piston.

•

Brake caliper cylinder “2”
Scratches/wear 

 Replace the brake caliper

assembly.

•

Brake caliper body “3”
Cracks/damage 

 Replace the brake caliper

assembly.

•

Brake fluid delivery passages
(brake caliper body)
Obstruction 

 Blow out with compressed air.

WARNING

EWA19270

When the brake caliper is disassembled, re-

place the brake caliper piston seal and the

brake caliper piston dust seal with new ones.

2. Check:

•

Brake caliper bracket
Crack/damage 

 Replace.

EAM30045

ASSEMBLING THE REAR BRAKE CALIPER

WARNING

EWA19280

• Before installation, clean and lubricate the

internal parts. Use new brake fluid for

1

2

1

2

3

Summary of Contents for WR250F 2022





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250F 2022

Baja motorsports BV250 Setup Instructions preview
BV250
Brand: Baja motorsports Pages: 8
Yukon Trail Badger 100 Owner'S Manual preview
Badger 100
Brand: Yukon Trail Pages: 24
Öhlins POF5K00 Mounting Instructions preview
POF5K00
Brand: Öhlins Pages: 2
Öhlins Mechatronics 35007-01 Installation Instruction preview
Mechatronics 35007-01
Brand: Öhlins Pages: 4
Öhlins McPherson Strut MIR 5H02 Mounting Instructions preview
McPherson Strut MIR 5H02
Brand: Öhlins Pages: 2
Öhlins KA 590 Mounting Instructions preview
KA 590
Brand: Öhlins Pages: 4
Yoshimura 14720BP520 Manual preview
14720BP520
Brand: Yoshimura Pages: 7
KEEWAY 125-2G Owner'S Manual preview
125-2G
Brand: KEEWAY Pages: 15
A.J.S. 350 1950 Maintenance Manual And Instruction Book preview
350 1950
Brand: A.J.S. Pages: 104
AGV AX-8 Dual Owner'S Instructions Manual preview
AX-8 Dual
Brand: AGV Pages: 64
AC Schnitzer AC S II Fitting Instructions Manual preview
AC S II
Brand: AC Schnitzer Pages: 44
Salewa Vayu User Manual preview
Vayu
Brand: Salewa Pages: 17
Yamaha TTR 125 2023 Manual preview
TTR 125 2023
Brand: Yamaha Pages: 90
Yamaha TT-R125(P) Owner'S Service Manual preview
TT-R125(P)
Brand: Yamaha Pages: 509
Yamaha TT-R125(N) Owner'S Service Manual preview
TT-R125(N)
Brand: Yamaha Pages: 508
Yamaha TT-R125(R) Owner'S Service Manual preview
TT-R125(R)
Brand: Yamaha Pages: 510
Yamaha TT-R125E(R) Owner'S Service Manual preview
TT-R125E(R)
Brand: Yamaha Pages: 578
Yamaha TT-R125(T) Owner'S Service Manual preview
TT-R125(T)
Brand: Yamaha Pages: 610

Brands by name

Popular brands

Load more brands