INSTALLING THE SPEAKER
When installing the speaker on the floor, attach the rubber spacers to the
underside of the speaker to provide support. Affix the rubber spacers firmly
when you attach them.
When installing the speaker on a wall or ceiling, use the included brackets
or optional U-bracket UB-DXR8. Ensure that the wall/ceiling is sufficiently
strong.
This package does not include the mounting hardware to install the
included brackets/safety wire or the UB-DXR8. If you are not sure what
materials are required for installation, consult a specialist.
An installed speaker is shown below. Install the bracket as shown.
WARNING
• Do not use the included brackets for ceiling installation.
• Do not use the UB-DXR8 for wall installation.
Pre-installation (Preparation of the cable)
Use stranded wire for cables attached to the Euroblock connector. Strip
their insulation as shown in the figure and connect them.
NOTE
Do not plate stranded wires by solder. Doing so will cause the wire to break.
Connect the cable from the amplifier to the “INPUT” socket, and the cable
being connected to other speakers to the “SATELLITE SPEAKERS”
socket.
A signal input to CH1 of INPUT is output from ST1 of SATELLITE
SPEAKERS, and signal input to CH2 of INPUT is output from ST2 of
SATELLITE SPEAKERS.
For VXS10ST/VXS10STW, connect the included 5-pin Euroblock
connector as shown below and set the appropriate wattage when using
100 V/70 V line.
NOTE
No setting should be made for 100 V line, as shown in the far left illustration.
1
Remove the Euroblock connector from the speaker.
Wall installation
(using included brackets)
Ceiling installation
(using optional bracket
UB-DXR8)
1
CONNECT THE WIRING TO THE CONNECTOR
100V/
×
70V/200W
100V/200W
70V/100W
100V/100W
70V/50W
100V/50W
70V/25W
About 7 mm (0.3 in.)
SATELLITE SPEAKERS
VXS10S/VXS10SW
VXS10ST/VXS10STW
INPUT
TRANSFORMER
SETTINGS
2
After loosening the terminal screws of the Euroblock connector with a
flat-blade screwdriver, insert the cable into each terminal and tighten
the screws. Make sure that cables cannot be pulled out.
NOTE
Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).
3
(VXS10ST/VXS10STW only) Plug the 5-pin Euroblock connector into
the TRANSFORMER SETTINGS socket.
1
Place the bracket base on the wall and
mark the position for screws/bolts. The
diameter of seven holes for screw/bolt
(not included) is ø6.5 mm.
2
Make holes in the wall for the bolts, as
required, and feed the bolts through
the holes.
3
Affix the bracket base on the wall. The
narrow edge of the bracket base
should be oriented downward.
4
Attach the mounting bracket to the speaker with the included screws
with captive washer.
The narrow edge of the mounting bracket should be oriented
downward.
5
Attach the two rubber spacers to the bottom edge of the speaker.
Make sure the spacers are located near the outer edge; otherwise,
they will impede installation on the bracket base in the next step.
Affix the rubber spacers firmly when you attach them.
6
Slide the speaker down onto the bracket base until it locks in place.
CAUTION
Be sure to perform this work with two or more people.
2
INSTALL THE SPEAKER
Installing on the wall (using the included brackets)
Euroblock connector
Less than 3 mm (0.1 in.)
Bracket base
Mounting bracket
Captive washer screw
Rubber spacer
Lock
Summary of Contents for VXS10S
Page 5: ......
Page 6: ......
Page 7: ...DIMENSIONS VXS10S VXS10SW Bracket base Mounting bracket ...
