Yamaha VX150C Owner'S Manual Download

Page: 97 / 120

5-2

C. Engine idles

irregularly or stalls.

Trouble

Possible Cause

Remedy

1. Spark plug(s) fouled or incorrect

type.

2. Fuel system obstructed.

3. Fuel contaminated or stale.

4. Fuel filter clogged.

5. Failed ignition parts.

6. Warning system activated.

7. Spark plug gap incorrect.

8. Poor connections or damaged

ignition wiring.

9. Specified engine oil not used.

10. Thermostat faulty or clogged.

11. Fuel pump damaged.

12. Air vent screw on the fuel tank

closed.

13. Choke knob pulled out.

14. Motor angle too high.

15. Fuel joint connection incorrect.

16. Throttle valve adjustment incorrect.

17. Battery lead disconnected.

1. Inspect spark plug(s). Clean or

replace with recommended type.

2. Check for pinched or kinked fuel

line or other obstructions in fuel

system.

3. Fill tank with clean, fresh fuel.

4. Clean or replace filter.

5. Have serviced by a Yamaha

dealer.

6. Find and correct cause of warning.

7. Inspect and adjust as specified.

8. Check wires for wear or breaks.

Tighten all loose connections.

Replace worn or broken wires.

9. Check and replace oil as specified.

10. Have serviced by a Yamaha

dealer.

11. Have serviced by a Yamaha

dealer.

12. Open the air vent screw.

13. Return to home position.

14. Return to normal operating

position.

15. Connect correctly.

16. Have serviced by a Yamaha

dealer.

17. Connect securely.

67M-9-15-5 1/30/03 9:46 Page 3

Summary of Contents for VX150C

























































































































Search results

Summary of Contents for VX150C

Reviews:

Related manuals for VX150C

Brands by name

Popular brands

Yamaha VX150C, Owner'S Manual

Search results

Summary of Contents for VX150C

Reviews:

Related manuals for VX150C

Brands by name

Popular brands