Yamaha VX Sport Owner'S Manual Download

Page: 96 / 106

Trouble recovery

(2) Remove any weeds or debris from

around the jet intake, drive shaft, impel-
ler, jet pump housing, and jet thrust noz-
zle.
If debris is difficult to remove, consult a
Yamaha dealer.

EJU34641

Jumping the battery

If the watercraft battery has run down, the en-
gine can be started using a 12-volt booster
battery and jumper cables.

EJU34663

Connecting the jumper cables

WARNING

EWJ01250

To avoid battery explosion and serious
damage to the electrical system:

●

Do not reverse the polarity of the jumper
cables when connecting to the batteries.

●

Do not connect the negative (–) jumper
cable to the negative (–) terminal of the
watercraft battery.

●

Do not touch the positive (+) jumper ca-
ble to the negative (–) jumper cable.

(1) Connect the positive (+) jumper cable to

the positive (+) battery terminals of both
batteries.

(2) Connect one end of the negative (–)

jumper cable to the negative (–) battery
terminal of the booster battery.

(3) Connect the other end of the negative (–)

jumper cable to an engine hanger.

(4) Start the engine, and then disconnect the

jumper cables by reversing the steps
above. (See page 32 for information on
starting the engine.)

EJU34695

Replacing the fuses

If a fuse is blown, replace it with the proper
fuse.

To replace a fuse:
(1) Remove the seat. (See page 44 for seat

removal and installation procedures.)

Negative (–) jumper cable

Booster battery

Positive (+) jumper cable

Engine hanger

Good fuse

Blown fuse

UF2N10E0.book Page 91 Tuesday, October 6, 2009 5:02 PM

Summary of Contents for VX Sport











































































































Search results

Summary of Contents for VX Sport

Reviews:

Related manuals for VX Sport

Brands by name

Popular brands

Yamaha VX Sport, Owner'S Manual

Search results

Summary of Contents for VX Sport

Reviews:

Related manuals for VX Sport

Brands by name

Popular brands