background image

Operation

28

ESU11290

Starting the engine 

WARNING

EWS00200

Be sure to check the “SAFETY INFOR-
MATION” section carefully before start-
ing the engine.

Make sure that the parking brake is ap-
plied.

NOTE:

Make sure that the engine stop switch is in the
on position. The starter motor cannot be oper-
ated when the engine stop switch is in the off
position.

1.

Fully open the starter (choke) lever.

NOTE:

The starter (choke) lever is not required when
the engine is warm. Put the starter (choke) le-
ver in the closed position.

2.

Turn the main switch to the start position.
After the engine starts, put the starter
(choke) lever in the half-open position.
Warm up the engine until it does not run
roughly or begin to stall when the starter
(choke) lever is returned to the closed po-
sition.

CAUTION:

ECS00330

Release the switch immediately after the
engine starts.

1. Starter (choke) lever

2. Fully open position (cold engine starting)

3. Half-open position (warming engine up)

4. Closed position (warm engine starting)

1. Start

U8GS11E0.book  Page 28  Friday, April 20, 2007  11:01 AM

Summary of Contents for VK10X

























































































Reviews: