Yamaha VK10X Owner'S Manual Download | Manualshive

Page: 37 / 88

background image

Operation

31

uphill side at all times. On climbs straight up
the hill, this can be accomplished by leaning
forward and, on steeper inclines, standing on
the running boards and leaning forward over
the handlebar. (Also see “Traversing a
slope”.)

Slow down as you reach the crest of the hill,
and be prepared to react to obstacles, sharp
drops, or other vehicles or people which may
be on the other side. If you are unable to con-
tinue up a hill, do not spin the track. Stop the
engine and set the parking brake. Then pull
the rear of the snowmobile around to point the
snowmobile back down the hill. When the
snowmobile is pointed downhill, mount your
snowmobile from the uphill side. Restart the
engine, release the parking brake, and de-
scend the hill.

WARNING

EWS00230

Side hills and steep slopes are not recom-
mended for a novice snowmobiler.

Riding downhill

When riding downhill, keep speed to a mini-
mum. It is important to apply just enough
throttle to keep the clutch engaged while de-
scending the hill. This will allow you to use en-
gine compression to help slow the
snowmobile, and to keep the snowmobile
from rolling freely down the hill. Also apply the
brake frequently, with light pressure.

WARNING

EWS00240

Use extra caution when applying the brake
during a descent. Excessive braking will
cause the drive track to lock, causing a
loss of control.

Traversing a slope

WARNING

EWS00250

Traversing slopes is not recommended for
a novice snowmobiler.

Traversing a slope requires you to properly
position your weight to maintain proper bal-
ance. As you travel across the slope, lean
your body to position your weight towards the
uphill side. A recommended riding position is
to kneel with the knee of your downhill leg on
the seat and the foot of your uphill leg on the
running board. This position will make it easi-
er for you to shift your body weight as needed.

U8GS11E0.book Page 31 Friday, April 20, 2007 11:01 AM

«
...
35
36
37
38
39
...
»

Summary of Contents for VK10X

























































































Reviews:

No comments

Related manuals for VK10X

Brand: KYMCO Pages: 89

Brand: UtilityDump Pages: 13

Brand: Taylor-Dunn Pages: 134

Brand: Cushman Pages: 158

2012 Prowler XT

Brand: Arctic Cat Pages: 64

1000 TRV LIMITED

Brand: Arctic Cat Pages: 84

Brand: Farr Pages: 156

2014 SNO PRO 500

Brand: Arctic Cat Pages: 90

Brand: Arctic Cat Pages: 68

Brand: Arctic Cat Pages: 80

Brand: Arctic Cat Pages: 76

2010 1000 H2 TRV

Brand: Arctic Cat Pages: 104

Brand: SILLA Pages: 52

Brand: PRONAR Pages: 166

1990 Electric Shuttle

Brand: Columbia Pages: 112

Brand: Jerr-Dan Pages: 104

IBT 4000 Series

Brand: IBEA Pages: 56

Brand: SANMEN COUNTY YONGFU MACHINE Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands