background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-34

6

XVS65AV/ATV

2. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

CAUTION:

ECA10680

Do not overtighten the screws, oth-
erwise the lens may break.

EAU24350

Supporting the motorcycle 

Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other maintenance
requiring the motorcycle to stand up-
right. Check that the motorcycle is in a
stable and level position before starting
any maintenance. A strong wooden
box can be placed under the engine for
added stability.

To service the front wheel

1. Stabilize the rear of the motorcycle

by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.

2. Raise the front wheel off the

ground by using a motorcycle
stand.

To service the rear wheel

Raise the rear wheel off the ground by
using a motorcycle stand or, if a motor-
cycle stand is not available, by placing

a jack either under each side of the
frame in front of the rear wheel or under
each side of the swingarm.

1. Screw

U3B61RE0.book  Page 34  Friday, June 10, 2005  2:10 PM

Summary of Contents for V-star XVS65V








































































































Reviews: