background image

IMPORTANT MANUAL INFORMATION

EAU10130

Particularly important information is distinguished in this manual by the following notations:

NOTE:

This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle
is subsequently sold.

Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most
current product information available at the time of printing, there may be minor discrepancies between your motorcycle
and this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.

WARNING

EWA10010

PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLY
AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE. DO NOT ATTEMPT TO OPERATE THIS MOTOR-
CYCLE UNTIL YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS 
INVOLVED!

Failure to follow WARNING instructions could result in severe injury or death to the 
motorcycle operator, a bystander or a person inspecting or repairing the motor-
cycle.

A CAUTION indicates special precautions that must be taken to avoid damage to 
the motorcycle.

A NOTE provides key information to make procedures easier or clearer.

WARNING

CAUTION:

NOTE:

U3B61RE0.book  Page 1  Friday, June 10, 2005  2:10 PM

Summary of Contents for V-star XVS65V








































































































Reviews: