15
Tyros3
7.
AJK Circuit Board
(Time Required: About 8 minutes)
7-1
Separate the upper case unit and lower case unit.
7-2
Remove the AC upper frame assembly. (See procedure 4.)
7-3
Remove the AC lower frame assembly with the power
supply unit on it (See procedure 6.)
7-4
Remove the VR knob (LINE IN/MIC [TRIM]). (Fig. 5)
7-5
Remove the four (4) screws marked [S03F] and six (6)
screws marked [S04B]. The AJK circuit board can then
be removed. (Fig. 5)
8.
ACIN Wiring Assembly
(Time Required: About 7 minutes)
8-1
Separate the upper case unit and lower case unit.
8-2
Remove the AC upper frame assembly. (See procedure 4.)
8-3
Remove the four (4) screws marked [S04C] and the
screw marked [S11]. The ACIN wiring assembly can
then be removed together with the power switch angle.
(Fig. 4)
8-4
Remove the two (2) screws marked [S01D]. The power
switch angle can then be removed. (Photo 2)
*
The push button is not part of the ACIN wiring
assembly. When replacing the ACIN wiring assembly
(push switch), remove the push button from the
push switch of the ACIN wiring assembly and install
it on the new ACIN wiring assembly. (Photo 2)
9.
SPOL Circuit Board, SPOR Circuit Board
(Time Required: About 6 minutes)
9-1
Separate the upper case unit and lower case unit.
9-2
Remove the two (2) screws marked [S04D]. The SPOL
circuit board can then be removed. (Fig. 5)
*
The SPOR circuit board can be removed in the same
way.
10.
CK Circuit Board
(Time Required: About 6 minutes)
10-1 Separate the upper case unit and lower case unit.
10-2
Remove the four (4) screws marked [S03G]. The CK
circuit board can then be removed. (Fig. 5)
11.
HP Circuit Board
(Time Required: About 6 minutes)
11-1 Separate the upper case unit and lower case unit. (See
11-2
Remove the three (3) screws marked [S03H]. The HP
circuit board can then be removed. (Fig. 5)
12. HDSB Circuit Board
(Time Required: About 6 minutes)
12-1 Separate the upper case unit and lower case unit.
12-2
Remove the two (2) screws marked [S01B] and four (4)
screws marked [S03I]. (Fig. 2, Fig. 5)
12-3 Pull off the HDSB circuit board from the HDD
terminal. (Photo 3)
POWER SWITCH ANGLE
POWER SWITCH ANGLE
[S01D]
PUSH SWITCH
PUSH BUTTON
PUSH BUTTON
PUSH SWITCH
Photo 2
HARD DISK DRIVE UNIT
HDSB
Photo 3
[S01]: BIND HEAD SCREW 3.0X6 MFZN2W3 (WE774000)
Summary of Contents for Tyros3
