Yamaha SXV70H Owner'S Manual Download Page 77

Page: 77 / 98

8-23

ESU00315

Control rod adjustment
For SXV70/SXV70ER

The weight transfer can be adjusted by turning the con-
trol rod adjusting nut

1. Loosen the locknut

while holding the control rod

adjusting nut

2. To increase weight transfer, turn the adjusting nut in

direction

. To decrease weight transfer, turn the

adjusting nut in direction

3. Tighten the locknut.

CAUTION:

●

When using the two 22-mm wrenches included in the
tool kit, make sure that they are situated at a right
angle to the control rod as shown, and that they are
tightly fitted to the locknut and the control rod adjust-
ing nut.

●

The left and right adjusting nuts must be set to the
same position. Uneven settings can cause poor han-
dling and loss of stability.

WARNING

Never adjust the control rods beyond the maximum
range indicated on the rods with red paint

Adjustable range

Standard position

Locknut tightening torque:

25 Nm (2.5 m·kgf, 18.1 ft·lb)

U8EK11.book Page 23 Thursday, April 25, 2002 5:10 PM

Summary of Contents for SXV70H



































































































Search results

Summary of Contents for SXV70H

Reviews:

Related manuals for SXV70H

Brands by name

Popular brands

Yamaha SXV70H, Owner'S Manual

Search results

Summary of Contents for SXV70H

Reviews:

Related manuals for SXV70H

Brands by name

Popular brands