Yamaha SXV70H Owner'S Manual Download Page 40 | Manualshive

Page: 40 / 98

background image

6-8

ESU00106

Battery

For SXV70ER

Check the fluid level and fill if necessary.
Use only distilled water if refilling is necessary. (See
page 8-29 for more details.)

ESU00239

Air filter

Always check that no snow is on the air filter element. If
there is any snow on the air filter element, take it out and
remove the snow. Then reinstall the air filter element
beneath the holding guides on the case. After riding the
snowmobile, make sure there is no snow on the air filter
element.

NOTE:

@

●

The air filter element can be removed when the ambi-
ent temperature is 5 °C (41.5 °F) or higher.

●

Before removing the air filter element, consult a
Yamaha dealer.

@

U8EK11.book Page 8 Thursday, April 25, 2002 5:10 PM

«
...
38
39
40
41
42
...
»

Summary of Contents for SXV70H



































































































Reviews:

No comments

Related manuals for SXV70H

Brand: Yamaha Pages: 26

Brand: Landoll Pages: 64

Brand: Bad Boy Pages: 56

Brand: Can-Am Pages: 58

Brand: Suzuki Pages: 140

Brand: U.S. General Pages: 23

Brand: QERIDOO Pages: 36

Brand: Yamaha Pages: 176

Brand: Yamaha Pages: 156

Workman 133-0959

Brand: Toro Pages: 8

Workman MDE 07299

Brand: Toro Pages: 44

Brand: Toro Pages: 56

Workman HDX 07383

Brand: Toro Pages: 68

Brand: SCORPION Pages: 32

Brand: Silverwing Pages: 20

Brand: SMC Networks Pages: 93

2000 INDY 600 XC SP EDGE

Brand: Polaris Pages: 2

1999 SCRAMBLER 500

Brand: Polaris Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands