Home
/
Yamaha
/
Star XVS13CAC
/
Owner'S Manual

Yamaha Star XVS13CAC, Owner'S Manual

Share

Page: 60 / 98

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-19

7

EAU50700

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure 5.0–10.0 mm (0.20–0.39 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.

1. Loosen the locknut at the clutch le-

ver.

2. To increase the clutch lever free

play, turn the clutch lever free play
adjusting bolt in direction (a). To
decrease the clutch lever free play,
turn the adjusting bolt in direction
(b).

TIP

If the specified clutch lever free play
could be obtained as described above,
skip steps 3–6.

3. Fully turn the adjusting bolt in di-

rection (a) to loosen the clutch ca-
ble.

4. Slide the rubber covers apart, and

then loosen the locknut.

5. To increase the clutch lever free

play, turn the clutch lever free play
adjusting nut in direction (a). To
decrease the clutch lever free play,
turn the adjusting nut in direction
(b).

6. Tighten the locknut at the clutch

cable, and then slide the rubber
covers to their original positions.

7. Tighten the locknut at the clutch le-

ver.

1. Clutch lever free play

2. Locknut (clutch lever)
3. Clutch lever free play adjusting bolt

3

(a)

(b)

2

1

1. Rubber cover

2. Locknut (clutch cable)
3. Clutch lever free play adjusting nut

(a)

1

(b)

1

2

3

U27D10E0.book Page 19 Thursday, July 22, 2010 1:05 PM

«
...
58
59
60
61
62
...
»

Summary of Contents for Star XVS13CAC



































































































Reviews:

No comments

Related manuals for Star XVS13CAC

Brand: Bajaj Auto Pages: 38

Brand: Yamaha Pages: 435

Brand: KTM Power Parts Pages: 7

SBL.04.650.10000/B

Brand: SW-Motech Pages: 2

Brand: Caberg Pages: 16

Brand: R&G Pages: 4

1999 Shadow Aero VT1100C3

Brand: Honda Pages: 226

Brand: Nuviz Pages: 46

Brand: LAS Pages: 22

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 2

Brand: DYNATEK Pages: 12

Brand: Kenwood Pages: 36

Brand: Kenwood Pages: 97

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

Brand: Rally-Raid Pages: 2

Brand: ChatterBox Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands