Yamaha Star XV250Y Owner'S Manual Download Page 69

Page: 69 / 94

PERIODIC MAINTENANCE AND ADJUSTMENT

7-34

a jack either under each side of the
frame in front of the rear wheel or under
each side of the swingarm.

EAU24360

Front wheel

EAU24601

To remove the front wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Disconnect the speedometer ca-

ble from the front wheel.

2. Loosen the front wheel axle pinch

bolt, then the wheel axle.

3. Lift the front wheel off the ground

according to the procedure on
page 7-33.

4. Pull the wheel axle out, and then

remove the wheel.

NOTICE:

not apply the brake after the
wheel has been removed to-
gether with the brake disc, oth-
erwise the brake pads will be
forced shut.

[ECA11071]

EAU24932

To install the front wheel

1. Install the speedometer gear unit

into the wheel hub so that the pro-
jections mesh with the slots.

1. Speedometer cable

1. Wheel axle
2. Front wheel axle pinch bolt

U46B10E0.book Page 34 Tuesday, May 20, 2008 7:32 PM

Summary of Contents for Star XV250Y































































































Search results

Summary of Contents for Star XV250Y

Reviews:

Related manuals for Star XV250Y

Brands by name

Popular brands

Yamaha Star XV250Y, Owner'S Manual

Search results

Summary of Contents for Star XV250Y

Reviews:

Related manuals for Star XV250Y

Brands by name

Popular brands