Yamaha Star XV250Y Owner'S Manual Download Page 61

Page: 61 / 94

PERIODIC MAINTENANCE AND ADJUSTMENT

7-26

EAU23111

Checking and lubricating the
throttle grip and cable

The operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated at
the intervals specified in the periodic
maintenance chart.

EAU44271

Checking and lubricating the
brake and shift pedals

The operation of the brake and shift
pedals should be checked before each
ride, and the pedal pivots should be lu-
bricated if necessary.

EAU23142

Checking and lubricating the
brake and clutch levers

The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be lu-
bricated if necessary.

Recommended lubricant:

Lithium-soap-based grease

Recommended lubricants:

Brake lever:

Silicone grease

Clutch lever:

Lithium-soap-based grease

U46B10E0.book Page 26 Tuesday, May 20, 2008 7:32 PM

Summary of Contents for Star XV250Y































































































Search results

Summary of Contents for Star XV250Y

Reviews:

Related manuals for Star XV250Y

Brands by name

Popular brands

Yamaha Star XV250Y, Owner'S Manual

Search results

Summary of Contents for Star XV250Y

Reviews:

Related manuals for Star XV250Y

Brands by name

Popular brands