Yamaha STAR XV19CSX Owner'S Manual Download

Page: 25 / 96

INSTRUMENT AND CONTROL FUNCTIONS

3-8

EAU12890

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAU13120

Fuel tank cap

To remove the fuel tank cap

Slide the lock cover open, insert the key
into the lock, and then turn it 1/4 turn
clockwise. The lock will be released
and the fuel tank cap can be removed.

To install the fuel tank cap

1. Insert the fuel tank cap into the

tank opening with the key inserted
in the lock and with the “

” mark

facing forward.

1. Brake lever

1. Brake pedal

1. Fuel tank cap lock cover

2. “

” mark

3. Unlock.
4. Lock.

U29S10E0.book Page 8 Friday, May 18, 2007 1:53 PM

Summary of Contents for STAR XV19CSX

































































































Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands

Yamaha STAR XV19CSX, Owner'S Manual

Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands