Yamaha Star 2010 Page 43 Owner'S Manual Download

Page: 43 / 104

OPERATION AND IMPORTANT RIDING POINTS

6-4

1600 km (1000 mi) and beyond

The vehicle can now be operated nor-
mally.

NOTICE

ECA10270

If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.

EAU17213

Parking

When parking, stop the engine, and
then remove the key from the main
switch.

WARNING

EWA10311

●

Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them and be burned.

●

Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.

●

Do not park near grass or other
flammable materials which
might catch fire.

U5S614E0.book Page 4 Friday, July 9, 2010 9:18 AM

Summary of Contents for Star 2010









































































































Search results

Summary of Contents for Star 2010

Reviews:

Related manuals for Star 2010

Brands by name

Popular brands

Yamaha Star 2010, Owner'S Manual

Search results

Summary of Contents for Star 2010

Reviews:

Related manuals for Star 2010

Brands by name

Popular brands