Yamaha Star 2010 Page 75 Owner'S Manual Download

Page: 75 / 104

PERIODIC MAINTENANCE AND ADJUSTMENT

7-32

5. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

6. Install the headlight bulb cover,

and then connect the coupler.

7. Install the headlight unit by install-

ing the bolts.

8. Place the turn signal/position light

bracket cover in the original posi-
tion, and then install the bolts.

9. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU24133

Replacing the tail/brake light
bulb

1. Remove the tail/brake light lens by

removing the screws.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

NOTICE:

Do not over-

tighten the screws, otherwise
the lens may break.

[ECA10681]

1. Headlight bulb holder
2. Headlight bulb

1. Screw

U5S614E0.book Page 32 Friday, July 9, 2010 9:18 AM

Summary of Contents for Star 2010









































































































Search results

Summary of Contents for Star 2010

Reviews:

Related manuals for Star 2010

Brands by name

Popular brands

Yamaha Star 2010, Owner'S Manual

Search results

Summary of Contents for Star 2010

Reviews:

Related manuals for Star 2010

Brands by name

Popular brands