Controls and Functions
10
STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual
D
REVERB TYPE/TIME control
Determines the reverb type and length. Turning the control to the right lengthens
the time of the selected reverb type.
HALL:
Simulated reverb of a large space, such as a concert hall.
PLATE:
Simulated metal plate reverb, producing a more hard-edged and bright
sound.
ROOM:
Simulated acoustic ambience of a small room.
ECHO:
Echo effect suitable for vocals.
E
REVERB controls (channels 1-4)
Determines the amount of reverb for each channel when the REVERB switch
C
is
on.
F
ST/MONO switches
STAGEPAS 600BT (channels 5/6, 7/8, 9/10)
STAGEPAS 400BT (channels 5/6, 7/8)
Setting the switch to ST (STEREO) (
N
) will assign the signals from the L and R
channels to each left and right speaker and output each signal. Setting the switch
to MONO (
O
) will mix the output of different L and R sources to output the same
signal to both the left and right speakers. For keyboards with mono output, guitars,
or other non-stereo sound sources, when the switch is set to MONO (
O
), the stereo
input jacks can be conveniently used as multiple mono jacks.
G
LEVEL meter
The LEVEL meter shows the level of output signal from the SPEAKERS L/R jacks.
Notice
If the unit is operated at a sufficiently high volume to make the LIMITER LED flashes
continuously, the internal power amplifier section is being excessively overloaded and may
malfunction. Reduce the output level with the MASTER LEVEL control so that the indicator
flashes only briefly on the highest transient peaks.
H
POWER LED
This LED lights when the power is turned on by pressing the power switch.
I
FEEDBACK SUPPRESSOR switch/LED
When this switch is on, the LED lights up, indicating that feedback is automatically
suppressed. (This configuration utilizes a seven-band notch filter. When this switch
or the power switch is off, the notch filter will be reset.)
J
LEVEL controls
Use these controls to adjust the volume for each channel. To reduce noise, set any
LEVEL controls on unused channels to the minimum.
K
MASTER EQ (equalizer) control
Use this control to adjust the overall sound frequency balance. The center position
“MUSIC” is a basic setting. If you turn the control counterclockwise, it will create an
optimum setting for speech, cutting unneeded low range frequencies. If you turn
the control clockwise, it will create an optimum setting for playback of sound
sources, since the low range is boosted. If you turn the control further clockwise,
the LED will light up, indicating that the bass boost function turns on, giving you an
even more powerful bass tone.
L
MASTER LEVEL control
Determines the volume of the signal output from the SPEAKERS L/R jacks. This
allows you to adjust the overall volume without changing the relative volume
balance among the various channels.
M
Vents
These are the vents for the cooling fan inside the mixer.
Do not block the vents when in use.
N
AC IN jack
Connect the included power cord here.
O
P
(power) switch
For turning the power of the mixer on (
O
) and off (
N
).
NOTE
Rapidly turning the unit on and off in succession may cause it to malfunction. After turning the
unit off, wait for about 5 seconds before turning it on again.
Summary of Contents for STAGEPAS 600BT
Page 1: ...Owner s Manual Mode d emploi Manual de instrucciones ES FR EN English Français Español ...
Page 28: ...68 STAGEPAS 600BT STAGEPAS 400BT Owner s Manual ...
Page 29: ...STAGEPAS 600BT STAGEPAS 400BT Owner s Manual 69 MEMO ...
Page 30: ...70 STAGEPAS 600BT STAGEPAS 400BT Owner s Manual MEMO ...
