Yamaha SRX 120 2017 Page 16 Operator'S Manual Download

Page: 16 / 30

Before removing the spark plug, be sure

to clean the area around the spark plug. If

you do not, dirt could enter engine when

removing or installing the spark plug.
Adjust the gap to specified amount (see

specifications chart) for proper ignition.

Use a feeler gauge to check the gap.

ATV0052B

When installing the spark plug, be sure to

tighten it securely. A new spark plug

should be tightened 1/2 turn once the

washer contacts the cylinder head. A

used spark plug should be tightened 1/8 -

1/4 turn once the washer contacts the cyl-

inder head.

Brake

Yamaha recommends that the complete

brake system be checked daily for wear

or damage and for smooth operation.

Periodically, the brake band should be

inspected for cracks and to ensure the

liner is intact and not worn excessively.

Replace the brake band if cracked or

worn excessively.

Checking Brake Lever

Travel

1. Compress the brake lever fully.
2. Check the distance between the

brake lever and the lever stop. The

distance must be within the specified

range of 6-13 mm (1/4-1/2 in.).

0725-565

3. If travel distance is not as specified,

adjust the brake.

Adjusting Brake Lever

Travel

To adjust the brake lever travel, use the

following procedure:

1. Remove the drive chain shield.
2. Loosen the rearward brake cable jam

nut; then tighten the forward jam nut

to set up the brake.

0735-457

3. Check the brake lever travel distance

periodically while tightening the for-

ward jam nut. When the distance is

within the specified range of 6-13 mm

(1/4-1/2 in.), tighten the rearward jam

nut to secure the adjustment.

Drive Chain

The drive chain should be lubricated every

10 operating hours with Yamaha Synthetic

Chain Lube. By using the recommended

chain lube or a dry, graphite-based chain

lubricant, dirt buildup on the drive chain

will be minimized. Before each lubrica-

tion, inspect the drive chain for dirt accu-

mulation.
To lubricate the drive chain, shut the engine

off and wait for all moving parts to stop,

remove the drive chain shield, and lubricate

the drive chain. After lubricating the drive

chain, install the drive chain shield.

! WARNING

DO NOT operate the snowmobile

when any component in the brake

system is damaged, worn, or

adjusted improperly.

Downloaded from

ManualsNet.com

search engine

Summary of Contents for SRX 120 2017































Search results

Summary of Contents for SRX 120 2017

Reviews:

Related manuals for SRX 120 2017

Brands by name

Popular brands

Yamaha SRX 120 2017, Operator'S Manual

Search results

Summary of Contents for SRX 120 2017

Reviews:

Related manuals for SRX 120 2017

Brands by name

Popular brands