Yamaha SR10ARLG Owner'S Manual Download

Page: 35 / 54

1. Remove the brake fluid reservoir

cover; then remove most of the

brake fluid from the reservoir. Install

the cover.



NOTE: The above procedure will

allow room for the fluid from the
caliper when the pistons are
pushed into the caliper for install-
ing new brake pads. Replacing the
cover will prevent fluid spillage.

2. Open the left-side access panel.
3. Remove the torx-head screws secur-

ing the brake shield to the belt guard

mount; then remove the cap screws

securing the brake shield to the

brake caliper.

4. Carefully move the shield out of the

way; then remove the hairpin clip

securing the brake pads to the cali-

per assembly.

5. Using a pair of pliers, pull the outer

brake pad out of the caliper assembly.

PC013



NOTE: Changing one pad at a

time will prevent one piston from
pushing out the other piston from
the caliper.

6. Measure the thickness of the brake pad.

The brake pad thickness must be greater

than 1.0 mm (0.04 in.). If the brake pad

thickness is less than specified, replace-

ment of both pads is necessary.

PC011A

7. Using a flat-blade tool, slowly and

carefully push the piston into the

caliper.

8. Position the outer brake pad into the

caliper; then install the hair-pin clip

into the caliper assembly.

9. Repeat steps 5-8 for the inner pad; then

secure the pad with the hairpin clip.

10. Remove the reservoir cover and

remove the remaining fluid; then fill

the reservoir with fresh fluid and

install the cover.

11. Pump the brake lever to ensure cor-

rect positioning of the brake pads

and proper brake lever travel; then

release.



NOTE: If brake lever travel is not

within specification, bleed the
brake system.

12. Remove the reservoir cover and fill

the reservoir (if necessary) to the

proper level with fresh brake fluid;

then install the cover.

13. Secure the brake shield, the driven

clutch (tightened to 20 ft-lb), and the

rear belt guard; then close and

secure the left-side access panel.



NOTE: When new brake pads are

installed, a “burnishing” process is
required (see Burnishing Brake
Pads sub-section).

Burnishing Brake Pads

After changing brake pads, the new brake

pads must be burnished to achieve full

braking effectiveness. Braking distance

will be extended until brake pads are

properly burnished.
To properly burnish the brakes, use fol-

lowing procedure:

CAUTION

Brake fluid is highly corrosive. Do
not spill brake fluid on any surface
of the snowmobile.

U8JRS2E0.book Page 30 Thursday, May 7, 2015 2:25 PM

Summary of Contents for SR10ARLG























































Search results

Summary of Contents for SR10ARLG

Reviews:

Related manuals for SR10ARLG

Brands by name

Popular brands

Yamaha SR10ARLG, Owner'S Manual

Search results

Summary of Contents for SR10ARLG

Reviews:

Related manuals for SR10ARLG

Brands by name

Popular brands