background image

8

Ring Mod.

Ring modulator.

Mod. Filter

Modulation filter.

Compressor

Compressor.

Parameter

Display

Range

Description

Source

SRC

OSC, SELF

Modulation source: oscillator or input signal

OSC Freq.

OSC

0.0 to 5000.0 Hz

Oscillator frequency

FM Freq.

FM.F

0.05 to 40.00 Hz

Oscillator frequency modulation speed

FM Depth

FM.D

0 to 100%

Oscillator frequency modulation depth 

Mix

MIX

0 to 100%

Mix level

Parameter

Display

Range

Description

Type

TYPE

Low Pass Filter, High Pass Filter, 
Band Pass Filter

Filter type: low pass, high pass, band pass

Freq.

FREQ

0.05 to 40.00 Hz

Modulation speed

Depth

DPTH

0 to 100%

Modulation depth

Phase

PHAS

0.00 to 354.38 degrees

Left-channel modulation and right-channel modulation phase differ-
ence 

Offset

OFST

0 to 100

Filter frequency offset

Resonance

RESO

0 to 20

Filter resonance

Level

LEVL

0 to 100

Output level

Mix

MIX

0 to 100%

Mix level

Parameter

Display

Range

Description

Comp. Threshold

THRE

-54.0 to 0.0 dB

Level at which compressor activates

Comp. Ratio

RATI

1:1 to 

:1

Compression ratio

Comp. Attack

ATAK

0 to 120 ms

Time required for compressor to peak after exceeding threshold

Comp. Release

RELE

6 to 11500 ms

Time required for compressor to terminate after going below threshold

Comp. Knee

KNEE

Hard, 1 to 5

Adjusts the width of the gain curve just above the threshold

Comp. Gain

GAIN

0.0 to 18.0 dB

Output level

Summary of Contents for Sound Editor ver. 2.10

































Reviews: