Yamaha RX-V665BL Owner'S Manual Download Page 68

Page: 68 / 94

Troubleshooting

“CHECK SP WIRES!”

appears on the front

panel display.

Speaker cables are short-circuited.

Make sure all speaker cables are connected correctly.

There is noise

interference from

digital or radio

frequency equipment.

This unit is too close to other digital or

radio frequency equipment.

Move this unit further away from such equipment.

—

The picture is

disturbed.

The video software is copy-protected.

This unit suddenly

enters the standby

mode.

The internal temperature becomes too

high and the overheat protection circuitry

has been activated.

Wait about 1 hour for this unit to cool down and then

turn it back on.

—

HDMI

Problem

Cause

Remedy

See

page

No picture or sound.

The number of the connected HDMI

components is over the limit.

Disconnect some of the HDMI components.

—

The connected HDMI component does not

support high-bandwidth digital copyright

protection (HDCP).

Connect an HDMI component that supports HDCP.

Tuner (FM/AM)

Problem

Cause

Remedy

See

page

FM stereo reception is

noisy.

You are too far from the station

transmitter or the input from the

antenna is weak.

Check the antenna connections.

Replace the outdoor antenna with a more

sensitive multi-element antenna.

—

Switch to monaural mode.

There is distortion, and

clear reception cannot

be obtained even with a

good FM antenna.

There is multi-path interference.

Adjust the antenna height or orientation, or

place it in a different location.

—

The desired station

cannot be tuned into

with the automatic

tuning method.

You are in an area far from a station or

an input from the antenna is weak.

Replace an outdoor antenna with more

sensitive multi element antenna.

—

Tune in manually or by direct frequency

tuning.

Problem

Cause

Remedy

See

page

Summary of Contents for RX-V665BL






























































































Search results

Summary of Contents for RX-V665BL

Reviews:

Related manuals for RX-V665BL

Brands by name

Popular brands

Yamaha RX-V665BL, Owner'S Manual

Search results

Summary of Contents for RX-V665BL

Reviews:

Related manuals for RX-V665BL

Brands by name

Popular brands