background image

38

SET MENU

1

2

3

This unit provides you with the following items on the SET
MENU to maximize the performance of your system and
expand your enjoyment for audio listening and video
watching.

1. CENTER SP
2. REAR SP
3. MAIN SP
4. BASS OUT
5. MAIN LVL
6. D.D. LFE
7. D-RANGE
8. DTS LFE
9. CNTR DELAY
10.MEM. GUARD
11.TV INPUT
12.CBL INPUT

Adjusting Items on the SET MENU

Adjustments should be performed with the remote control
while watching the information on the display.

1

Set the selector dial to the
AMP/TUN (or DSP/TUN)
position.

2

Press SET MENU
repeatedly to select the
item you want to adjust.

The selected item appears on
the display.

y

After pressing SET MENU once, you can also select the item by
pressing 

d

.  (Pressing 

u

 goes back one selection.)

3

Press 

i

 or 

j

 repeatedly to

adjust the setting.

4

Repeat steps 2 and 3 to adjust the setting of
any other item in the same way.

Memory back-up

The memory back-up circuit prevents the stored data
from being lost when this unit is set in the standby mode.
If, however, the power cord is disconnected from the AC
power outlet or the power is cut for more than one week,
the settings of the SET MENU will automatically return
to the preset positions and values. If so, adjust the
settings of the SET MENU again.

0108V596RDS38-44_EN

2/29/0, 3:30 PM

38

Summary of Contents for RX-V596RDS







































































Reviews: