Yamaha RoadStan XV17AMC Owner'S Manual Download Page 38 | Manualshive

Page: 38 / 107

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-18

3

With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Shift the transmission into the neutral position.
5. Push the start switch.

Does the engine start?

With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.

Does the engine stall?

After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.

Does the engine start?

The system is OK.

The motorcycle can be ridden.

This check is most reliable if performed with
a warmed-up engine.

The neutral switch may be defective.

The motorcycle should not be ridden

until

checked by a Yamaha dealer.

The sidestand switch may be defective.

The motorcycle should not be ridden

until

checked by a Yamaha dealer.

The clutch switch may be defective.

The motorcycle should not be ridden

until

checked by a Yamaha dealer.

YES

NO

YES

NO

YES

NO

NOTE:

U5VN13E0.book Page 18 Monday, May 15, 2006 2:13 PM

«
...
36
37
38
39
40
...
»

Summary of Contents for RoadStan XV17AMC












































































































Reviews:

No comments

Related manuals for RoadStan XV17AMC

Brand: Xenith Pages: 17

Brand: GAS GAS Pages: 34

Brand: Baja motorsports Pages: 20

Brand: Suzuki Pages: 440

Daytona 955i 2002

Brand: Triumph Pages: 384

Brand: hepco & becker Pages: 2

Brand: Xenith Pages: 7

Brand: Shad Pages: 12

XSM POWER UP 2007

Brand: Malaguti Pages: 53

Brand: SPmoto Pages: 92

Brand: Royal Alloy Pages: 40

Brand: Honda Pages: 206

Brand: Janus Pages: 96

Brand: Hobart Pages: 20

Brand: Honda Pages: 79

Bullet 350 2019

Brand: Royal Enfield Pages: 68

Brand: Rewaco Pages: 42

Brand: Honda Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands