Yamaha RoadStan XV17AMC Owner'S Manual Download Page 22 | Manualshive

Page: 22 / 107

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-2

3

EAU11003

Indicator and warning lights

EAU11020

Turn signal indicator light “

”

This indicator light flashes when the
turn signal switch is pushed to the left or
right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

”

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU38100

Fuel level warning light “

”

This warning light comes on when the
fuel level drops below approximately
3.5 L (0.92 US gal) (0.77 Imp.gal).
When this occurs, turn the fuel cock le-
ver to the “RES” position and refuel as
soon as possible.

NOTE:

This model is also equipped with a self-
diagnosis device for the fuel level de-
tection circuit. If the fuel level detection
circuit is defective, the following cycle
will be repeated until the malfunction is
corrected: The fuel level warning light
will flash eight times, and then go off for
3.0 seconds. If this occurs, have a
Yamaha dealer check the vehicle.

EAU11500

Engine trouble warning light “

”

This warning light comes on or flashes
when an electrical circuit monitoring the
engine is defective. When this occurs,
have a Yamaha dealer check the self-
diagnosis system.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. If the warning light does not come
on for a few seconds, then go off, have
a Yamaha dealer check the electrical
circuit.

1. Fuel level warning light “

”

2. High beam indicator light “

”

3. Turn signal indicator light “

”

4. Neutral indicator light “

”

5. Engine trouble warning light “

”

U5VN13E0.book Page 2 Monday, May 15, 2006 2:13 PM

«
...
20
21
22
23
24
...
»

Summary of Contents for RoadStan XV17AMC












































































































Reviews:

No comments

Related manuals for RoadStan XV17AMC

RACE 13100CP520

Brand: Yoshimura Pages: 7

GearTronic ZERO GT3100-K1

Brand: PZRacing Pages: 2

Brand: Termignoni Pages: 9

Brand: Spartus Pages: 24

Brand: Yamaha Pages: 112

Brand: Aim Pages: 47

BOOMERANG 7554CB

Brand: Bagster Pages: 2

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 226

Brand: hepco & becker Pages: 3

Brand: GMX Pages: 14

Brand: Honda Pages: 173

Brand: Rothewald Pages: 96

Brand: R&G Pages: 4

Brand: Dakota Digital Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands