Yamaha R-V902 Owner'S Manual Download Page 39 | Manualshive

Page: 39 / 44

background image

39

LEARNING A NEW FUNCTION

1

Place this remote control transmitter and the other
remote control transmitter so that they face each other.

2

* If there is no operation for about 30 seconds after the

LEARN button is pressed, the TRANSMIT/LEARN indicator
flashes rapidly and the current mode is canceled. If this
occurs, repeat this step.

3

If necessary, select the memory area by using the A/B/C
switch on the side panel of the remote control
transmitter.

4

Press the key on this remote control transmitter in which
you will store a new function.

* If a key which cannot learn another function is pressed, the

TRANSMIT/LEARN indicator flashes rapidly and the current
mode is canceled. If this occurs, repeat this step.

* If there is no operation for about 30 seconds after a key is

pressed, the TRANSMIT/LEARN indicator flashes rapidly
and the mode before you began learning operations is
restored. If this occurs, restart from step 2.

5

Press and hold the key (on the other remote control
transmitter) which has the function you want to store.

* When learning is finished, the TRANSMIT/LEARN indicator

stops lighting and then begins flashing slowly.

* If a signal is not successfully received, the

TRANSMIT/LEARN indicator flashes rapidly and the mode
prior to step 4 is restored. If this occurs, restart from step 4.

* If memory capacity is full, the TRANSMIT/LEARN indicator

flashes rapidly to show you that learning is impossible, and
then the mode before you began learning operations is
restored.

6

Repeat step 3–5 to store more functions.

7

When you finish the learning operation, press the
LEARN button.

Notes

●

Newly learned functions will replace previously learned
functions.

●

If there is no more room in the memory area for a function to
be learned, the TRANSMIT/LEARN indicator will flash
rapidly. In this case, even if some keys are not occupied
with functions from other remote control transmitters, no
further learning is possible.

●

If the lid is closed while learning and about 5 seconds pass,
the TRANSMIT/LEARN indicator flashes rapidly and the
mode before you began learning operations is restored. If
this occurs, restart from step 2. However, if the lid is opened
within 5 seconds, the mode before the lid was closed is
restored.

●

There may occasionally be instances in which, due to the
signal-coding and modulation employed by the other remote
control transmitter, this remote control transmitter will not be
able to “learn” its signals.

V-AUX

PHONO

EFFECT

ON/OFF

1

2

3

SPORTS

STADIUM

DISCO

TV

4

5

6

AZZ CLUB

CHURCH

9

TEST

V-AUX

PHONO

EFFECT

ON/OFF

1

2

3

SPORTS

STADIUM

DISCO

TV

4

5

6

ROCK

JAZZ CLUB

CHURCH

7

8

9

HALL

EVEL

TEST

UME

+1

0

Lights up.

V-AUX

PHONO

EFFECT

ON/OFF

1

2

3

SPORTS

STADIUM

DISCO

TV

4

5

6

JAZZ CLUB

CHURCH

8

9

TEST

This remote control
transmitter

Other remote
control transmitter

About 5–10 cm
(2–4 in.)

TRANSMIT

/LEARN

LEARN

CLEAR

MACRO

Flashes slowly.

(Press by using the point of
a mechanical pencil, etc.)

LEARN

CLEAR

MACRO

«
...
37
38
39
40
41
...
»

Summary of Contents for R-V902













































Reviews:

No comments

Related manuals for R-V902

Brand: Jensen Pages: 11

Brand: Jensen Pages: 24

Brand: Jensen Pages: 22

MP6211 - Radio / CD

Brand: Jensen Pages: 52

Brand: Jensen Pages: 2

Brand: Jensen Pages: 16

Brand: Jensen Pages: 3

Brand: Jensen Pages: 9

Heavy Duty JHD40BT

Brand: Jensen Pages: 2

Brand: Streetwize Pages: 2

Brand: Teac Pages: 14

VM8013HD - Screen MultiMedia Receiver

Brand: Jensen Pages: 3

Brand: Blaupunkt Pages: 17

Brand: Mutant Pages: 40

Brand: Harman Kardon Pages: 24

Brand: Interlogix Pages: 27

Brand: Dittel Pages: 38

Brand: Lafayette Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands