background image

NS-AP8600/SPS-8600

11

SPEAKER PLACEMENT

This speaker is designed to be used as a front, center, surround or effects speaker.

— Front speaker

 placement should be separated by a distance of  6–10ft. If they are placed too close together, 

there will be a reduction in the stereo effect. Conversely, If placed too for apart, the so called “middle-
omission” effect will  occur and the vocal center fill will be lost. Height of the speaker should be at least at ear 
level.

— Center channel speakers

 should be placed centered above or below the TV.

— Surround speakers

 should ideally be placed behind the listening area, at least as far apart as the front 

speakers and up to 2 additional feet apart per side. The height of the speaker should be at a minimum of ear 
level or preferably somewhat higher.

SPECIFICATIONS

Type  

2-way Acoustic Suspension

Speaker: Woofer  

Dual 3” High Compliance Pulp Cone and Rubber surround

Speaker: Tweeter  

1/2” Balanced Dome

Frequency Range  

90 Hz–50 kHz (-10 dB)

Impedance  

6 ohms

Nominal Input  

30 W

Maximum Input  

100 W

Sensitivity (dB/2.83v. 1m)  

82 dB/w.m

Crossover Frequency  

2.5 kHz

Dimension (H x W x D)  
 

NS-AP8500S  

11-7/8” x 3-5/8” x 4” (300 x 92 x 102 mm) (Satellite)

 

NS-AP8500C 

3-5/8” x 11-7/8” x 4” (92 x 300 x 102 mm) (Center)

 

SPS-8500 

31-5/8” x 3-5/8” x 9-7/8” (800 x 92 x 250 mm) 

Weight
 

NS-AP8500S/NS-AP8500C   2.6 lbs (1.2 kg)

 

SPS-8500  

7.7 lbs (3.5 kg)

Magnetic Shielding  

Yes

*Specifications subject to change without notice due to product improvements.

Left Front Speaker

Right Front Speaker

Left Surround Speaker

Right Surround Speaker

Center Speaker

6

10 feet

up to approx 
2 feet more

up to approx 
2 feet more

LISTENING AREA

Summary of Contents for NS-AP8600













Reviews: