background image

 

1

ME02R96

ENGLISH

DEUTSCH

FRANÇAIS

ESP

A

Ñ

OL

 

ME02R96 

Owner’s Manual

 

Thank you for your purchase of the YAMAHA ME02R96 memory expansion kit for the 02R96 mixer.

By replacing the original CPU board with this ME02R96 expansion board, you will expand your

mixer’s automix memory to 7MB—a sevenfold increase that will make your mixer even more versa-

tile and even easier to use.

Please read through the following precautions carefully before having the serviceperson install this

ME02R96 expansion kit. Be sure to retain the manual in a safe place.

 

Precautions

 

WARNINGS

 

Failure to observe the following warnings may lead to fatality or serious injury from fire or

electric shock.

 

CAUTIONS

 

Failure to observe the following cautions may lead to injury, or may result in damage to

equipment or other property.

 

 

Do not attempt to disassemble or modify the
ME02R96 board. Do not apply excessive force to
board connectors or other board components.
(Mishandling of the board may lead to shock, fire
hazard, or equipment failure.)

 

 

Be sure to unplug the 02R96 main unit from the
power supply before installing the ME02R96
board (to eliminate shock hazard).

 

 

Be careful to avoid catching or snagging fingers
while carrying out the installation.

 

 

Before starting installation, be sure to save all
important data from the 02R96 unit to an external
MIDI device. This installation process will clear all
of the unit’s user memory and will reset all set-
tings to their defaults.

 

 

When handling the ME02R96 board, do not
touch the board’s metallic leads (pins). (Pins are
sharp and may cause hand cuts.)

 

 

The ME02R96 board is electrostatic-sensitive.
Before handling the board, you should briefly
touch the main unit’s metal casing with your bare
hand so as to drain off any static charge from
your body.

 

 

Be sure to install the included lithium battery. This
is a backup battery that is required maintain the
data in the 02R96’s expanded memory.

The ME02R96 expansion kit must be installed by an authorized
serviceperson. Please contact a local Yamaha dealer or a service
center to arrange for installation. Do not attempt to install the
ME02R96 on your own. 

Summary of Contents for ME02R96










Reviews: