Yamaha LZ150C Owner'S Manual Download Page 81

Page: 81 / 120

4-14

106092

EMU00369*

CHECKING FUEL SYSTEM

Gasoline (petrol) and its vapors are highly
flammable and explosive. Keep away
from sparks, cigarettes, flames or other
sources of ignition.

Check the fuel line for leaks, cracks, or
malfunctions. If any problem is found, it
should be repaired immediately by a
Yamaha dealer or other qualified mechan-
ic.

Checking points

Fuel system parts leakage.

Fuel hose joint leakage.

Fuel hose cracks or other damage.

Fuel connector leakage.

Leaking fuel can result in fire or explo-
sion.

Check for fuel leakage regularly.

If any fuel leakage is found, the fuel
system must be repaired by a qualified
mechanic. Improper repairs can make
the outboard unsafe to operate.

EMU16350

CHECKING TOP COWLING

Check the fitting of the top cowling by
pushing it with both hands.
If the fitting is loose have it repaired by a
Yamaha dealer.

68F-9-15-4 2/28/03 9:38 AM Page 15

Summary of Contents for LZ150C

























































































































Search results

Summary of Contents for LZ150C

Reviews:

Related manuals for LZ150C

Brands by name

Popular brands

Yamaha LZ150C, Owner'S Manual

Search results

Summary of Contents for LZ150C

Reviews:

Related manuals for LZ150C

Brands by name

Popular brands