Yamaha HTR5930B Owner'S Manual Download Page 22 | Manualshive

Page: 22 / 74

background image

18

CONNECTIONS

Both FM and AM indoor antennas are supplied with this
unit. In general, these antennas should provide sufficient
signal strength. Connect each antenna correctly to the
designated terminals.

• The AM loop antenna should be placed away from this unit.
• A properly installed outdoor antenna provides clearer reception

than an indoor one. If you experience poor reception quality,
install an outdoor antenna. Consult the nearest authorized
YAMAHA dealer or service center about outdoor antennas.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

■

Connecting the AM loop antenna

1

Set up the AM loop antenna.

2

Press down the tab of the AM ANT terminal.

3

Insert the one of the AM loop antenna lead
wires into the AM ANT terminal.

4

Release the tab back to secure the wire.

5

Repeat steps 2 through 4 to connect the
other lead wire to the GND terminal.

Once you have properly connected the AM loop
antenna to this unit, orient the AM loop antenna for
the best reception when you tune into AM stations.

Connecting the FM and AM antennas

Notes

AM

ANT

GND

FM

ANT

TUNER

AM loop

antenna

(supplied)

Ground

For maximum safety and minimum
interference, connect the antenna GND
terminal to a good earth ground. A good
earth ground is a metal stake driven into
moist earth.

Indoor FM
antenna
(supplied)

Outdoor AM antenna

Use a 5 to 10 m (16 to 32 ft) of
vinyl-covered wire extended
outdoors from a window.

«
...
20
21
22
23
24
...
»

Summary of Contents for HTR5930B











































































Reviews:

No comments

Related manuals for HTR5930B

Brand: JBL Pages: 6

Brand: Renault Pages: 384

eXtreme HD mini

Brand: FTE Maximal Pages: 46

Brand: Blaupunkt Pages: 28

Brand: Icom Pages: 47

Brand: Yaesu Pages: 96

Brand: Team Electronic Pages: 27

Brand: Daewoo Pages: 125

Brand: Muzak Pages: 3

Brand: SAL Pages: 60

Brand: D+M Group Pages: 24

A1560 SONIC Series

Brand: ACS Pages: 20

Brand: Manta Pages: 20

Brand: Chamberlain Pages: 2

Brand: TYT Pages: 48

Brand: elv Pages: 8

Brand: Magnadyne Pages: 12

Brand: Strong Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands