18
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
EDITING EFFECT PROGRAMS
Effect programs can be edited in the Edit mode. Once you’ve edited a program, you can save it
to a User memory location. (See SAVING EFFECT PROGRAMS on page 31.)
CAUTION!
■
Be careful not to press the
p
button at any time during editing. Doing so
will call up the original effect program’s settings and erase all settings you had made to that
point.
OPERATION
1
Select an effect program for editing and press the
e
button to enable the Edit mode.
(The EDIT/COMPARE lamp lights and the ON/OFF
lamp above Pedal Switch B flashes.)
2
Use Pedal Switches 1 – 5 to turn on the desired
effect blocks.
HINT
■
Since you’ll probably want to listen to the
changes as you make them, make sure that all
relevant effect blocks are turned on. Better yet, turn off
all blocks except the one you are editing. This lets you
clearly hear only the effect you wish to edit. (One
possible exception to this guideline is the Amp Simula-
tor effect, changes to which are easier to hear when
Distortion is also on.)
3
Use the
y
and
n
buttons to select the
desired effect block row (in the parameter matrix
printed on the panel). (The lamp at the left of the
corresponding block lights.)
NOTE
■
The TUNER/METRONOME row cannot be
selected in the Edit mode.
4
Use the Parameter Dials to adjust the effect param-
eters.
Parameter Dial A is used to change the effect type of
the selected block; B – E are used to change the
corresponding parameters.
In the example shown below, the EQ/AMP block has
been selected.
•••••••••••••••••••••••••••••••••••••••••••••••••
A
B
C
D
E
COPY / SWAP / WRITE
MEMORY NO.
NO
YES
•••••
••••••
•••
•••
•••
•••
•••
•••
••••••••
••••••••••••••••••••••
PARAM
CHECK
•••
•••
COMP
DIST /
INSERT
EQ / AMP
DELAY
REVERB
N.GATE/UTIL
TUNER/
METRONOME
MOD 2
MOD 1
ATTACK
PRE-DRIVE*
LOW / —
TIME
TIME
THRESHOLD
SPEED
PITCH / PITCH L
ENHANCE / SENSE
SENSE
DRIVE
MID / —
FB
TONE
VOLUME POSITION
BEAT
(14~88 = 1/4~8/8)
DEPTH
— / PITCH R
FREQUENCY
—
TONE
HIGH / TONE
MIX
MIX
MINIMUM VOLUME
TEMPO
(60~86.=60~186)
TONE / FB
MIX
MIX / RANGE
LEVEL
LEVEL
LEVEL
TOTAL LEVEL
CLICK LEVEL
(1 LO 2 MID 3 HI)
ON/OFF
(SWITCH 4)
1 EQ / 2 STACK 3 COMBO 4 TUBE
————---
1~3 OD, DIST1,2 (DI*+AN) 4,5 OD*+DIST1,2
6~11 OD, DIST1,2+INSERT 12 INSERT
————---
————---
TUNING PITCH
(0~5 = 440~445Hz)
1 CHORUS / 2 FLANGER 3 PHASER
4 PITCH SHIFT / 5 DETUNE
6 EXCITER / 7 TOUCH WAH 8 PEDAL WAH
1 HALL 2 ROOM 3 STAGE 4 PLATE
ON/OFF
(SWITCH 5)
—
Use these to select
the desired block
for editing. (In this
example, EQ/AMP
is selected.)
Selects the type of
effect. (In this
example, 1 EQ is
selected.)
Adjusts the LOW parameter for the
EQ effect. (The dash indicates that
no parameter is available for the
other effects.)
Adjusts the MID parameter
for the EQ effect. (The dash
indicates that no parameter
is available for the other
effects.)
Adjusts the HIGH
parameter for the EQ effect
and the TONE parameter
for the others.
Adjusts
the LEVEL
parameter.
