manualshive.com logo in svg

Yamaha Grizzly 450 YFM45FGPD, Owner'S Manual, Page: 7 / 172

Share
Download
Yamaha Grizzly 450 YFM45FGPD Owner'S Manual Download Page 7

EBU17330

IMPORTANT MANUAL INFORMATION

EBU17342

FAILURE TO FOLLOW THE WARNINGS CONTAINED IN THIS MANUAL CAN RESULT IN SERIOUS IN-
JURY OR DEATH.
Particularly important information is distinguished in this manual by the following notations:

* Product and specifications are subject to change without notice.

This is the safety alert symbol. It is used to alert you to potential per-
sonal injury hazards. Obey all safety messages that follow this sym-
bol to avoid possible injury or death.

A WARNING indicates a hazardous situation which, if not avoided, 
could result in death or serious injury.

A NOTICE indicates special precautions that must be taken to avoid 
damage to the vehicle or other property.

A TIP provides key information to make procedures easier or clearer.

WARNING

NOTICE

TIP

U1CT62E0.book  Page 1  Friday, May 11, 2012  9:03 AM

Summary of Contents for Grizzly 450 YFM45FGPD













































































































































































Reviews:

No comments