Yamaha Grizzly 450 YFM45FGPD Owner'S Manual Download Page 60

Page: 60 / 172

5-6

Tire information

This ATV is equipped with tubeless tires with
valves.

WARNING

EWB02551

Use of improper tires on this ATV may cause
loss of control, increasing your risk of an acci-
dent.

After extensive tests, only the tires listed below
have been approved for this model by Yamaha
Motor Manufacturing Corporation of America.

1. Tire wear limit

Front:

Manufacturer/model:

YFM450FAD CHENG SHIN/C-828
YFM450FAPD CHENG SHIN/C-828
YFM45FGD MAXXIS/MU13
YFM45FGPAD MAXXIS/MU13
YFM45FGPD MAXXIS/MU13
YFM45FGPHD MAXXIS/MU13

Size:

AT25 x 8-12

Type:

Tubeless

Rear:

Manufacturer/model:

YFM450FAD CHENG SHIN/C-828
YFM450FAPD CHENG SHIN/C-828
YFM45FGD MAXXIS/MU14
YFM45FGPAD MAXXIS/MU14
YFM45FGPD MAXXIS/MU14
YFM45FGPHD MAXXIS/MU14

Size:

AT25 x 10-12

Type:

Tubeless

U1CT62E0.book Page 6 Friday, May 11, 2012 9:03 AM

Summary of Contents for Grizzly 450 YFM45FGPD













































































































































































Search results

Summary of Contents for Grizzly 450 YFM45FGPD

Reviews:

Yamaha Grizzly 450 YFM45FGPD, Owner'S Manual, Page: 60 / 172

Search results

Summary of Contents for Grizzly 450 YFM45FGPD

Reviews: