Yamaha FZ6-NA Owner'S Manual Download Page 60 | Manualshive

Page: 60 / 92

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-19

6

“broken in”. Therefore, it is ad-
visable before doing any high-
speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.

●

The tires must be warmed up
before a high-speed run.

●

Always adjust the tire air pres-
sure according to the operating
conditions.

EAU21960

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

EAU22080

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.
To increase the clutch lever free play,
turn the adjusting bolt in direction (a).
To decrease the clutch lever free play,
turn the adjusting bolt in direction (b).

1. Clutch lever free play adjusting bolt

2. Clutch lever free play

U5S3E0E0.book Page 19 Tuesday, September 19, 2006 9:37 AM

«
...
58
59
60
61
62
...
»

Summary of Contents for FZ6-NA





























































































Reviews:

No comments

Related manuals for FZ6-NA

Brand: Caberg Pages: 16

Brand: Yamaha Pages: 88

Brand: BMW Pages: 176

Bonneville T100

Brand: Triumph Pages: 198

Stelvio 1200 MY11 2011

Brand: MOTO GUZZI Pages: 385

Brand: MOTO GUZZI Pages: 209

Brand: Yamaha Pages: 596

Brand: Yamaha Pages: 578

Brand: DYNATEK Pages: 8

GHJ 10,8+18V Unisex

Brand: Bosch Pages: 14

Brand: Bosch Pages: 28

Brand: Bosch Pages: 145

Brand: Saddlemen Pages: 6

Brand: SW-Motech Pages: 2

HPS.11.258.900-01

Brand: SW-Motech Pages: 2

TRT.00.787.32500/B

Brand: SW-Motech Pages: 6

Brand: BMW Motorrad Pages: 28

Brand: BMW Motorrad Pages: 170

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands