Yamaha FZ6-NA Owner'S Manual Download Page 56 | Manualshive

Page: 56 / 92

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-15

6

WARNING

EWA12471

Be sure to place the hoses in their
original position as shown.

8. Install the seat.

EAU34300

Adjusting the engine idling
speed

The engine idling speed must be
checked and, if necessary, adjusted as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.
The engine should be warm before
making this adjustment.

NOTE:

The engine is warm when it quickly re-
sponds to the throttle.

Check the engine idling speed and, if
necessary, adjust it to specification by
turning the idle adjusting screw. To in-
crease the engine idling speed, turn the
screw in direction (a). To decrease the
engine idling speed, turn the screw in
direction (b).

NOTE:

If the specified idling speed cannot be
obtained as described above, have a
Yamaha dealer make the adjustment.

1. Original position (paint mark)

1. Idle adjusting screw

Engine idling speed:

1250–1350 r/min

U5S3E0E0.book Page 15 Tuesday, September 19, 2006 9:37 AM

«
...
54
55
56
57
58
...
»

Summary of Contents for FZ6-NA





























































































Reviews:

No comments

Related manuals for FZ6-NA

Rocky Mountain-EXP SB-1

Brand: Wolfman Pages: 7

Brand: KTM Pages: 13

Brand: LSL Pages: 12

V125 Special 2018

Brand: Lambretta Pages: 53

Brand: Honda Pages: 330

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 100

Road Star XV17AWX

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 650

Brand: Arai Pages: 2

Brand: JETPRIME Pages: 4

Brand: Sealey Pages: 2

Brand: Sealey Pages: 2

Brand: Sealey Pages: 2

Brand: Sealey Pages: 2

Brand: Sealey Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands