Yamaha FJR1300S(C) Owner'S Manual Download | Manualshive

Page: 60 / 99

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-18

6

EAU21380

Adjusting the throttle cable
free play

The throttle cable free play should mea-
sure 3.0–5.0 mm (0.12–0.20 in) at the
throttle grip. Periodically check the
throttle cable free play and, if neces-
sary, have a Yamaha dealer adjust it.

EAU21400

Adjusting the valve clearance

The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.

EAU21750

Tires

To maximize the performance, durabil-
ity, and safe operation of your motor-
cycle, note the following points
regarding the specified tires.

Tire air pressure

The tire air pressure should be checked
and, if necessary, adjusted before each
ride.

WARNING

EWA10500

●

The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).

●

The tire air pressure must be ad-
justed in accordance with the
riding speed and with the total
weight of rider, passenger, car-
go, and accessories approved
for this model.

1. Throttle cable free play

5JW11.book Page 18 Friday, May 9, 2003 4:03 PM

«
...
58
59
60
61
62
...
»

Summary of Contents for FJR1300S(C)




































































































Reviews:

No comments

Related manuals for FJR1300S(C)

Easyrack 6622520 01 01

Brand: hepco & becker Pages: 4

Brand: LAMAX Pages: 134

Brand: KYMCO Pages: 69

Stelvio 1200 4V

Brand: MOTO GUZZI Pages: 135

Brand: klicbag Pages: 2

Brand: Ohlins Pages: 4

Brand: SUOMY Pages: 84

Brand: Nolan Pages: 80

Mambo Evo PURE CARBON

Brand: LAZER Pages: 13

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 360

Brand: Yamaha Pages: 580

Brand: Yamaha Pages: 98

YZF-R1P 2001-2003

Brand: Yamaha Pages: 26

Brand: Yamaha Pages: 36

Brand: Yamaha Pages: 47

Brand: Yamaha Pages: 87

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands