Yamaha FJR1300AS(X) Service Manual Download Page 207

Page: 207 / 754

FRONT WHEEL

4-20

2. Check:

• Tire
• Front wheel

Damage/wear

→

Replace.

Refer to “CHECKING THE TIRES” on page
3-40 and “CHECKING THE WHEELS” on
page 3-42.

3. Measure:

• Radial wheel runout “1”
• Lateral wheel runout “2”

Over the specified limits

→

Replace.

4. Check:

• Wheel bearings

Front wheel turns roughly or is loose

→

Re-

place the wheel bearings.

• Oil seals

Damage/wear

→

Replace.

EAS22010

MAINTENANCE OF THE FRONT WHEEL
SENSOR AND SENSOR ROTOR

CAUTION:

ECA3P6D004

• Handle the ABS components with care

since they have been accurately adjusted.
Keep them away from dirt and do not sub-
ject them to shocks.

• The front wheel sensor cannot be disas-

sembled. Do not attempt to disassemble it.
If faulty, replace with a new one.

• Keep magnets (including magnetic pick-up

tools, magnetic screwdrivers, etc.) away
from the wheel sensor rotor.

• Do not drop or shock the wheel sensor or

the wheel sensor rotor.

1. Check:

• Front wheel sensor “1”

Cracks/bends/distortion

→

Replace.

Iron powder/dust

→

Clean.

2. Check:

• Front wheel sensor rotor “1”

Cracks/damage/scratches

→

Replace the

front wheel sensor rotor.
Iron powder/dust/solvent

→

Clean.

NOTE:

• The wheel sensor rotor is installed on the inner

side of the wheel hub.

• When cleaning the wheel sensor rotor, be

careful not to damage the surface of the rotor
magnet.

3. Measure:

• Wheel sensor rotor deflection

Out of specification

→

Clean the installation

surface of the wheel sensor rotor and correct
the wheel sensor rotor deflection, or replace
the wheel sensor rotor.

Radial wheel runout limit

1.0 mm (0.04 in)

Lateral wheel runout limit

0.5 mm (0.02 in)

Summary of Contents for FJR1300AS(X)



















































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FJR1300AS(X)

Reviews:

Related manuals for FJR1300AS(X)

Brands by name

Popular brands

Yamaha FJR1300AS(X), Service Manual

Search results

Summary of Contents for FJR1300AS(X)

Reviews:

Related manuals for FJR1300AS(X)

Brands by name

Popular brands