background image

Operation

37

Dispose of rags properly according to local
laws or regulations.

8.

Turn the fuel tank cap clockwise to tight-
en until a click is heard.

9.

Turn the air vent screw clockwise to close
it.

EMU27452

Operating engine

WARNING

EWM00420

Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstructions.
Be sure there are no swimmers in the
water near you.

When the air vent screw is loosened,
gasoline vapor will be released. Gaso-
line is highly flammable, and its vapors
are flammable and explosive. Refrain

from smoking, and keep away from
open flames and sparks while loosening
the air vent screw.

This product emits exhaust gases which
contain carbon monoxide, a colorless,
odorless gas which could cause brain
damage or death when inhaled. Symp-
toms include nausea, dizziness, and
drowsiness. Keep cockpit and cabin ar-
eas well ventilated. Avoid blocking ex-
haust outlets.

EMU44560

Sending fuel (portable tank)

1.

To loosen the air vent screw, turn it coun-
terclockwise until it stops.

2.

Check the direction of the fuel hose.
Make sure that the arrow of the primer
pump points toward the outboard motor.

1. Fuel tank cap

1. Air vent screw

1

ZMU07449

1

ZMU07444

1. Air vent screw

1. Toward the outboard motor

2. Arrow

1

ZMU07445

ZMU07452

1

4

3

2

U60R3BE0.book  Page 37  Thursday, May 2, 2013  8:59 AM

Summary of Contents for F8



















































































Reviews: