Yamaha F225C Owner'S Manual Download

Page: 81 / 92

Maintenance

Single engine

Twin engines

EMU29371

Disconnecting the battery

Turn off the battery cut-off switch (if
equipped) and main switch.

NOTICE:

they are left on, the electrical system
can be damaged.

[ECM01930]

Disconnect the negative cable(s) from
the negative (-) terminal.

NOTICE:

Al-

ways disconnect all negative (-) ca-
bles first to avoid a short circuit and
damage to the electrical system.

[ECM01940]

1. Isolator lead with circuit protection

2. Red cable

3. Black cable
4. Fuse

5. Battery for accessories

6. Battery for starting
7. Negative connecting cable

ZMU05939

1. Starboard side engine

2. Port side engine

3. Red cable
4. Black cable

5. Isolator leads with circuit protection

6. Fuse
7. Battery for starting

8. Battery for accessories

9. Negative connecting cable

ZMU05941

U6P276E0.book Page 75 Wednesday, April 1, 2009 9:44 AM

Summary of Contents for F225C





























































































Search results

Summary of Contents for F225C

Reviews:

Related manuals for F225C

Brands by name

Popular brands

Yamaha F225C, Owner'S Manual

Search results

Summary of Contents for F225C

Reviews:

Related manuals for F225C

Brands by name

Popular brands