Yamaha F150D Owner'S Manual Download | Manualshive

Page: 43 / 80

background image

Operation

37

4.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever toward
you to support the engine.

WARNING

EWM00260

After tilting the outboard motor, be sure to
support it with the tilt support knob or tilt
support lever. Otherwise the outboard mo-
tor could fall back down suddenly if oil in
the power trim and tilt unit loses pressure.

5.

Models equipped with trim rods: Once the
outboard motor is supported with the tilt
support lever, press the power trim and
tilt switch “

” (down) to retract the trim

rods.

CAUTION:

ECM00250

Be sure to retract the trim rods completely
during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt
mechanism.

EMU28052

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt sup-
port lever / tilt support knob becomes
free.

2.

Release the tilt support lever or pull out
the tilt support knob.

3.

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

DN

ZMU01936

UP

DN

U63P12E0.book Page 37 Friday, March 12, 2004 10:29 AM

«
...
41
42
43
44
45
...
»

Summary of Contents for F150D

















































































Reviews:

No comments

Related manuals for F150D

Brand: Gigabyte Pages: 51

Brand: MATSONIC Pages: 78

Brand: Texas Instruments Pages: 17

Freescale MC9S08MM128

Brand: NXP Semiconductors Pages: 12

Brand: Qiyangtech Pages: 16

Brand: IEI Technology Pages: 162

Brand: DFI Pages: 107

Brand: Gigabyte Pages: 39

Brand: Daewoo Pages: 46

Brand: Gigabyte Pages: 2

Brand: Aaeon Pages: 139

Brand: Asus Pages: 84

Brand: Asus Pages: 49

Infinity NF650I Ultra

Brand: DFI Pages: 155

MBD-X11SDV-12C-TP8F

Brand: Supermicro Pages: 123

Brand: Analog Devices Pages: 16

EVAL-AD5761RSDZ

Brand: Analog Devices Pages: 17

Brand: ASROCK Pages: 107

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands