manualshive.com logo in svg

Yamaha F150D, Owner'S Manual

Share
Download
Yamaha F150D Owner'S Manual Download Page 24

Basic components

18

NOTE:

The water separator and engine trouble warn-
ing indicators only operate when the engine is
equipped with the appropriate functions.

EMU26521

Low oil pressure warning indicator

If oil pressure drops too low, the warning indi-
cator will start to blink. For further information,
see page 25.

CAUTION:

ECM00020

●

Do not continue to run the engine if the
low oil pressure warning indicator is on
and the engine oil level is lower. Serious
engine damage will occur.

●

The low oil pressure warning indicator
does not indicate the engine oil level.
Use the oil dipstick to check the remain-
ing oil quantity. For further information,
see page 28.

EMU26581

Overheat warning indicator (digital 
type)

If the engine temperature rises too high, the
warning indicator will start to blink. For further
information on reading the indicator, see page
24.

CAUTION:

ECM00050

Do not continue to run the engine if the
overheat warning indicator is on. Serious
engine damage will occur.

EMU26600

Speedometer (digital type)

This gauge shows the boat speed.

1. Tachometer

2. Trim meter

3. Hour meter

4. Low oil pressure warning indicator
5. Overheat warning indicator

6. Set button

7. Mode button

ZMU01840

1

5

2

4

3

6

7

1. Low oil pressure warning indicator

1. Overheat warning indicator

ZMU01736

1

ZMU01737

1

U63P12E0.book  Page 18  Friday, March 12, 2004  10:29 AM

Summary of Contents for F150D

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands