Yamaha F100D Owner'S Manual Download | Manualshive

Page: 67 / 100

background image

Operation

61

2.

Press the power trim and tilt switch “

”

(up) until the outboard motor has tilted up
completely.

3.

Pull the tilt support lever toward you to
support the engine.

WARNING! After

tilting the outboard motor, be sure to
support it with the tilt support knob or
tilt support lever. Otherwise the out-
board motor could fall back down sud-
denly if oil in the power trim and tilt
unit or in the power tilt unit loses pres-
sure.

[EWM00262]

NOTICE:

Do not use the

tilt support lever or knob when traile-
ring the boat. The outboard motor
could shake loose from the tilt support
and fall. If the motor cannot be trail-
ered in the normal running position,
use an additional support device to
secure it in the tilt position. For more
detailed information, see page 66.

[ECM01641]

4.

Models equipped with trim rods: Once the
outboard motor is supported with the tilt
support lever, press the power trim and

UP

ZMU04232

U6D779E0.book Page 61 Tuesday, November 15, 2011 2:33 PM

«
...
65
66
67
68
69
...
»

Summary of Contents for F100D





































































































Reviews:

No comments

Related manuals for F100D

Brand: Telit Wireless Solutions Pages: 5

Brand: Aeroflex Pages: 20

Brand: DFI Pages: 99

Brand: Texas Instruments Pages: 101

ML501MicroBlaze

Brand: Xilinx Pages: 46

Brand: ASROCK Pages: 27

Brand: austriamicrosystems Pages: 19

Linear DC2681A-A

Brand: Analog Devices Pages: 8

Brand: ECS Pages: 74

Brand: Supero Pages: 78

Brand: ASROCK Pages: 26

Z68A-G45 B3 Series

Brand: MSI Pages: 138

Brand: Acrosser Technology Pages: 3

Brand: Biostar Pages: 210

Brand: Gigabyte Pages: 96

Brand: Gigabyte Pages: 38

Brand: IEI Technology Pages: 163

Brand: JETWAY Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands