manualshive.com logo in svg

Yamaha F-20B, Owner'S Manual

Share
Download
Yamaha F-20B Owner'S Manual Download Page 58

Operation

51

3. Push the tilt support knob into the clamp

bracket to support the engine.

WARNING! After tilting the outboard
motor, be sure to support it with the
tilt support knob or tilt support lever.
Otherwise the outboard motor could
fall back down suddenly if oil in the
power trim and tilt unit or in the pow-
er tilt unit loses pressure.

 [EWM00263]

NOTICE:

 Do not use the tilt support

lever or knob when trailering the
boat. The outboard motor could
shake loose from the tilt support and
fall. If the motor cannot be trailered in
the normal running position, use an
additional support device to secure it
in the tilt position. For more detailed
information, see page 55.

 [ECM01642]

EMU30193

Procedure for tilting down (manual 
tilt models)

1. Place the tilt lock lever in the lock posi-

tion.

2. Slightly tilt the engine up until the tilt sup-

port bar is automatically released.

3. Slowly tilt the engine down.

ZMU05580

UP

ZMU04884

ZMU05541

ZMU05528

6AG-9-79-1E0.book  51 ページ  ２０１４年１１月１０日　月曜日　午後４時８分

Summary of Contents for F-20B































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands