Yamaha EF7200DE, EF7200D Service Manual Download Page 68

Page: 68 / 178

4-1

CARB

REMOVING THE CARBURETOR

Order

Job/Parts to remove

Q’ty

Remarks

Removing the carburetor

Remove the parts in the order listed.

Negative battery lead

Turn the fuel cock lever to the “OFF”
position.
Disconnect.
EF7000E/EF7200E/EF7200DE

Carrier frame

Refer to “HANDLE AND WHEELS (FOR
EF7200DE CAN)” on 3-23.

Fuel tank

Refer to “FUEL TANK, CANISTER” on 3-7.

Air filter

Refer to “AIR FILTER” on 3-6.

Fuel cut solenoid valve lead

Auto choke lead

EF7000E/EF7200E/EF7200DE

Carburetor assembly

CARBURETOR

For complete information about procedures for carburetor maintenance, it is necessary to refer
to the MZ SERIES ENGINE SERVICE MANUAL 7VB-F8197-E0.

REMOVING THE CARBURETOR

Summary of Contents for EF7200DE, EF7200D



















































































































































































Search results

Summary of Contents for EF7200DE, EF7200D

Reviews:

Related manuals for EF7200DE, EF7200D

Brands by name

Popular brands

Yamaha EF7200DE, EF7200D, Service Manual

Search results

Summary of Contents for EF7200DE, EF7200D

Reviews:

Related manuals for EF7200DE, EF7200D

Brands by name

Popular brands