Yamaha EF5500D Owner'S Manual Download Page 64

Page: 64 / 72

– 59 –

For EF5500D

ENGINE DOES NOT START

Pull the recoil starter and check the spark

plug for spark strength.

(See “WARNING”)

WARNING

To prevent FIRE HAZARDS be sure

fuel is not present in the spark plug

area.

To prevent FIRE HAZARDS be sure

to place the spark plug as far way

as possible from the spark plug

hole and carburetor area.

To prevent ELECTRIC SHOCK do

not hold spark plug lead with hand

while testing.

Does not spark

Turn the engine switch to “

” (ON), then

pull the recoil starter and check if the oil
warning light flickers.

791-001e

Does not flicker

Flickers

Check engine oil level.

Level low

Consult a

Yamaha dealer.

Add engine oil.

Check the spark plug.

Type: BPR4ES (NGK)

Gap: 0.7–0.8 mm (0.028–0.031 in)

Incorrect

Replace or

adjust gap.

Clean the spark
plug.

Consult a Yamaha dealer.

Check the following.

Fuel line clogging

Air filter element clogging

Clogged

Clean or
replace.

Engine does not start.

7P5-F8199-14.indd 59

2021/06/23 11:22:20

Summary of Contents for EF5500D









































































Search results

Summary of Contents for EF5500D

Reviews:

Related manuals for EF5500D

Brands by name

Popular brands

Yamaha EF5500D, Owner'S Manual

Search results

Summary of Contents for EF5500D

Reviews:

Related manuals for EF5500D

Brands by name

Popular brands