manualshive.com logo in svg

Yamaha DX150A, Owner'S Manual

Share
Download
Yamaha DX150A Owner'S Manual Download Page 35

E

2-12

P S

mpg

Km/L

gph

I/h

ECON SYNC

TTL

FUEL MANAGEMENT

EMU00145

Warning indicator

8

Fuel warning

If the fuel level decreases to one segment
the fuel level warning segment 

1

begins

blinking.

8

Low battery voltage warning

If battery voltage drops, the display 

2

will

be automatically turned on and it begins
blinking.

c

C

Do not continue to operate the engine if a
warning device has activated. Refer to
the TROUBLESHOOTING section in this
manual. Consult a Yamaha dealer if the
problem cannot be located and corrected.

802031

TRIP

TIME

BATT

Km/h

knot

mph

km

mile

SPEED

YAMAHA

set

mode

q

w

YAMAHA

set

mode

P S

mpg

Km/L

gph

I/h

ECON SYNC

TTL

FUEL MANAGEMENT

q

w

e

EMU00146

FUEL MANAGEMENT METER

Optional equipment

The meter contains the fuel flow meter,
fuel consumption meter, fuel economy
meter, twin engine speed synchronizer,
water separator warning indicator.

1

Fuel flow meter

2

Fuel consumption / Fuel economy meter /
Twin engine speed synchronizer

3

Water separator warning indicator
(Operates only if the sensor has been
installed.)

NOTE:

After the main switch is first turned on, all
portions of the meter come on as a check.
After a few seconds, the meters will
change to normal operation. Watch the
meter when turning on the main switch to
make sure all segments come on.

 67N-9-13-2  4/19/01 5:08 PM  Page 13

Summary of Contents for DX150A




























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands