background image

SPEC

E

GENERAL SPECIFICATIONS

Outdrive Specifications

GENERAL SPECIFICATIONS

             Model name

Items

Upper (Driven/Drive)

Gear ratio

Lower (Driven/Drive)
Total

Clutch system
Drive unit oil capacity

Drive unit recommended oil

Mounting form
Steering system
Steering angle
Tilt/trim system
Tilt angle
Trim angle

Power trim/pump recommended oil

Power trim/tilt system oil capacity
Propeller driving system
Exhaust system

Cooling system

Lubricating system

Transom length
(crankshaft center – cavitation plate)
Weight
(dry, without power steering cylinder)
Power steering

INT

INT-HD (6U00)

Drive    DE-DHT-C (6U41)

DE-DHT-D (6U51)

35/30

35/30

26/17

26/18

1.78

1.68

Hydraulic clutch system

2.4 L

2.45 L

Yamaha Stern Drive Gear Oil or Hypoid Gear

Oil (SAE90) GL-4, GL-5 or equivalent

Direct mounting on transom, gimbal ring type

Steering guide system
30

°

 each, right and left

Hydraulic tilt/trim system

46.5

°

 (in reference to 13

°

 transom)

– 6

°

 to 15

°

 (in reference to 13

°

 transom)

Automatic Transmission Fluid (ATF)

Dexron Type II.

0.82 L

Spline drive system

Through propeller hub

Inlet on the lower case side, seawater pump

located at the front of the engine

Integrated (upper and lower) oil chamber and

oil pump

351.5 mm

107 kg

Standard

2-1

Summary of Contents for DE-DHT


















Reviews: