Yamaha CYGNUS RAY ZR 2022 Supplementary Service Manual Download

Page: 45 / 163

CABLE ROUTING

2-26

SPEC

CABLE ROUTING (For Drum) - Chassis (Front view)

Turn signal relay

Wire harness (headlight assembly)

Main switch coupler

Horn lead

Seat lock cable

Leg shield

Inner fender

Main switch lead

UBS brake cable

Wire harness (Front turn signal light assem-
bly) shall be attached with leg shield hook.

Wire harness shall not be slack in this area.

Route the seat lock cable through the out side
of leg shield and inner fender.

Route the seat lack cable through the out side
of leg shield boss.

Main switch lead shall be attached with leg
shield hook.

Seat lock cable shall be attached with leg
shield hook.

B2UF8197E1.book Page 26 Wednesday, October 6, 2021 4:38 PM

Summary of Contents for CYGNUS RAY ZR 2022




































































































































































Search results

Summary of Contents for CYGNUS RAY ZR 2022

Reviews:

Related manuals for CYGNUS RAY ZR 2022

Brands by name

Popular brands

Yamaha CYGNUS RAY ZR 2022, Supplementary Service Manual

Search results

Summary of Contents for CYGNUS RAY ZR 2022

Reviews:

Related manuals for CYGNUS RAY ZR 2022

Brands by name

Popular brands